CK5 - The Full-Size GM Off Road Community

Google
Web ColoradoK5.com

PDA

View Full Version : need a 14bsf

steve_kibbe
10-26-2006, 06:42 PM
I would prefere 6 lug with 3.73's or 4.10's:wink1:

What ya got??
Col_Sanders
10-26-2006, 06:55 PM
Heading back out to pick n pull tomorrow. I'll let you know if I see another one.
steve_kibbe
10-26-2006, 06:58 PM
Thanks:D
WRENCH-HEAD
10-26-2006, 07:41 PM
I just got a SF with 3.73's and 6 lug. Too bad I'm in Colorado, I don't need it anymore and no one seems to want it.
steve_kibbe
10-26-2006, 08:20 PM
how much for the axles and gears just in case I fing a housing:D
extremetahoe
10-26-2006, 08:20 PM
Would you mind looking for a 14bff pinion yoke for me while you are at it? Let me know how much. Would greatly appreciate it.
ryan22re
10-26-2006, 09:58 PM
How about a set of one tons Steve?
lamberthkp
10-27-2006, 03:57 AM
how much for the axles and gears just in case I fing a housing:D

i have a housing.
steve_kibbe
10-27-2006, 05:20 AM
How about a set of one tons Steve?
Sure...how much:D
steve_kibbe
10-27-2006, 05:20 AM
i have a housing.

How much?
steve_kibbe
10-27-2006, 05:38 AM
I'd take 4.10's too:D
Gorillajeep
10-27-2006, 06:27 AM
I just got a SF with 3.73's and 6 lug. Too bad I'm in Colorado, I don't need it anymore and no one seems to want it.

Why not? Would this not be a good substitute for a 12 bolt? Or is it not that much stronger?

James
clarkjw24
10-27-2006, 06:44 AM
Why not? Would this not be a good substitute for a 12 bolt? Or is it not that much stronger?

James

Its stronger, larger shafts, larger ring and pinion but still uses the c-clip axle shafts vs. the full floaters.
clarkjw24
10-27-2006, 06:45 AM
I would prefere 6 lug with 3.73's or 4.10's:wink1:

What ya got??


Why not just toss a 14ff in there and run adaptors?
steve_kibbe
10-27-2006, 07:07 AM
Too easy John... how much are the adapters??

I was also thinking about ground clearance.
lamberthkp
10-27-2006, 07:33 AM
Steve sent ya a pm
Cajun4x4
10-27-2006, 07:36 AM
Too easy John... how much are the adapters??

I was also thinking about ground clearance.

:wink1:

http://www.trinity.edu/tfrancis/Class/1320/ElecPneumTools/PortaBandSaw.JPG
steve_kibbe
10-27-2006, 07:41 AM
I have a 14bff with 4.10's in my gmc I've thought about stealing, but its still 8 lug.

Where can I get a 8 to 6 lug spacer/adapter?

Oh yea, I shaved it already;)
Cajun4x4
10-27-2006, 07:43 AM
you could prolly 8 lug your front for close to what adapters would cost...
steve_kibbe
10-27-2006, 07:48 AM
I have a 8 lug front 10 bolt from the same truck...but I would need tires and wheels, which I already have 6 lug stuff....
Cajun4x4
10-27-2006, 08:07 AM
ahh... well i tried:doah:
clarkjw24
10-27-2006, 08:14 AM
Adaptors prob around $150 to $200 but you can always sell them after you convert the front.
steve_kibbe
10-27-2006, 08:19 AM
John, where can I get the adapters, I've been looking, but no luck.
steve_kibbe
10-27-2006, 08:22 AM
Now I'm thinking about just swapping my 3/4's for my 1/2's...

I have a nice set of 16x8 8 lugs I could use for dd, then I could sell the 6 lug 16x10's I used durring the thump and buy a set of 16x8-10's for my tsl's....

Damn, this is tempting:doah: :rolleyes: