CK5 - The Full-Size GM Off Road Community

(6) Monroe shocks for stock K5 $30
Stock front leaf springs (2 leaves) $25
Stock front leaf speings (3 leaves) $30 <font color="red"> SOLD </font>
(2 pairs) stock front shackles $10
Stock swaybar off m1008 $20
6.2L battery trays (both) $10 <font color="red"> SOLD </font>
6.2L diesel air cleaner (no hardware) $10
NP208 shifter $20
(2) flange style front CV's only $20 each
Stock D60 steering arm $20
Stock 10 bolt steering arm $10
Stock tie rod off m1008 $20

Stock rear driveshaft off my 88 K5 (NP208). Recently new slip yoke, upper spicer u-joint and lower conversion 1350 spicer u-joint. Can provide measurments if needed.
$65

Can get pics if interested. Prices do not include shipping.

Thanks

How are the battery trays, rust etc? and passenger side correct? i call dibs.

PM'd/e-mailed you. It's late, I'm punchy. /forums/images/graemlins/rolleyes.gif

What kinda shape are the 3 leaf leaf springs in? Could you get me rough deminsions and weight (trying to figure shipping(looks like about $20))? If they will take away the negative arch I have, I'll take 'um!! Let me know what kinda shipping options you have (unless you want to meet in the middle)

Alec78

please ignore this post. Don't ignore the one for getting the springs.

OK, let's try here. /forums/images/graemlins/smile.gif

Send me a pic for the air cleaner &amp; let me know what "no hardware" means plz.

TIA,
Eric D
88 K5 -&gt; http://www.lvmt.net/1988k5/page_01.htm

[ QUOTE ]
How are the battery trays, rust etc? and passenger side correct? i call dibs.


[/ QUOTE ]

Battery trays have some light surface rust here and there where the factory coating has come off. A good cleaning and painting would be good. Yes, they are the passenger side. Here is a pic:
http://coloradok5.com/photos/data/500/1736Jun25_44-med.JPG

[ QUOTE ]
PM'd/e-mailed you. It's late, I'm punchy.

[/ QUOTE ]
Emailed you about the air cleaner and sent some pics too. No hardware means, no snorkle, studs, or wingnuts.

[ QUOTE ]
What kinda shape are the 3 leaf leaf springs in? Could you get me rough deminsions and weight (trying to figure shipping(looks like about $20))? If they will take away the negative arch I have, I'll take 'um!! Let me know what kinda shipping options you have (unless you want to meet in the middle)

[/ QUOTE ]

The leaf springs are in good shape from what we can tell. They were on an 86 m1008 with 44,000 miles on it. When we got the m1008, it was sitting up well and didn't have an engine, tranny or t-case. The springs measure 46 3/4" eye to eye and 3" wide at the spring eyes. They weigh approximately 90lbs, so that should give you an idea on shipping. My zip is 74134 if you want to figure shipping. Here is a pic:
http://coloradok5.com/photos/data/500/1736Jun25_48-med.JPG

Dog not included /forums/images/graemlins/wink.gif

Thanks
Ross

hey thanks for the pic, im going to pass didnt know they were out of a cucv. I have a set of those already.

I'm interested in the rear driveshaft. Can you send me the measurements?

Sent you a PM on the springs!

I'll take those battery trays if they are not spoken for. Can you check on shipping to BA, OK 74014?
Thanks

Just heard you work in Sapulpa. Maybe I could just pick them up?

[ QUOTE ]
I'm interested in the rear driveshaft. Can you send me the measurements?

[/ QUOTE ]

I will get measurements after I get home from work

[ QUOTE ]
I'll take those battery trays if they are not spoken for. Can you check on shipping to BA, OK 74014?
Thanks

Just heard you work in Sapulpa. Maybe I could just pick them up?

[/ QUOTE ]

You are next in line for the trays. If you want them they are yours. I actually live in Tulsa and work in Sapulpa. My dad bought your 36's from you, so I'm sure we can work something out on picking them up. I'll see after I get home from work if my dad still has your number and we can go from there.

Sounds good! /forums/images/graemlins/thumb.gif

[ QUOTE ]
I'm interested in the rear driveshaft. Can you send me the measurements?

[/ QUOTE ]

Here ya go:

29 1/4" ctr u-joint to ctr u-joint
37 1/2" end to end
6" slip yoke


DP 90K5
PM me with your number and we can arrange something for the trays.


Thanks
Ross

Updated on original post

Up again