K5 Blazer Forums  
Home of the 1969-91 K5 Blazer/Jimmy including GM Trucks and Suburbans.  
Go Back   CK5 Forums > General Discussion > The Garage

Remove these ads.

Reply
 
Thread Tools Display Modes
Old 09-24-2007, 11:01 PM   #1
jonrpick
Supporting Member
Registered User
 
jonrpick's Avatar
 
Join Date: Jun 2005
Location: Marietta, GA
Posts: 8,767

i Trader: (0 )

How do I know if my transfer case is going out?

I'm trying to wrap my mind around the fact that I just tore down my rear axle and the bearings look good.

So, when the rear axle (with less than 5k miles on it) "died" I took it into Pep Boys. Bad idea, yes...but I figured they could at least diagnose the problem. They're the ones that said it was a bad pinion bearing. But they would only have known that if they'd torn it down, right???

Ok...while it was on the rack, they checked a few things. One thing they mentioned was that the transfer case would probably need a rebuild soon. They said it had metal shavings in it.

So I get the K5 back to Atlanta, and it's in the garage. The transfer case leaks...

...

If it ran out of fluid, it would start shaving off metal. It doesn't matter that I've mainly used it in 2WD, there's still moving parts in it when I'm going down the street.

Prior to tearing down the axle, these were the symptoms:

Noise and slight vibration begins before I hit 10mph.
Noise increases with speed, but better when the drivetrain is under load (acceleration).
When cruising, or no load (just maintaining speed) it's unbearable and scary.
Not so bad when decelerating (negative load).

The drivetrain is 700R4 --> NP208 --> 10-bolt with 3.73's.

Discuss...please
__________________
Jon R. Pickens / Marietta, GA / '86 K5, stock
Myspace

Quote:
Originally Posted by chalet2506 View Post
If you've been pubed, and your willing to slap a little butt nectar on a man's phone, the rules just went out the window.
Quote:
Originally Posted by runamok151 View Post
who cares what color the wig is. i'm pulling it off and whipping her ass w/ it no matter what color it is.
My avatar is indicative of my attitude...
jonrpick is online now   Reply With Quote
Sponsored Links



Remove these ads.
Old 09-25-2007, 06:40 AM   #2
obijuan
Registered User
 
obijuan's Avatar
 
Join Date: May 2006
Location: San Antonio TX
Posts: 3,974

i Trader: (11 )

GM of the month Winner
umm what i would do is basically set it in N and chock the wheels. then while its in N move the slip yoke part of the shaft at the tailhousing up and down to see if theres excessive play. if there is it could be the bushing at the end of the tailhousing. then take the shaft out and check for play in the output shaft in all directions. could be a bad bearing somewhere. and then finally i would take the fill plug out and check for fluid level/condition and chain tightness.
after that, im out of ideas. tell us your findings.
obijuan is offline   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -7. The time now is 12:51 AM.


Powered by vBulletin® Version 3.8.1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.